How to Thread a Sewing Machine

Threading a sewing machine will become second nature to you, but only after you practice it a few times. However, for someone who has never sewn before, it could seem like a really difficult process.

This five-step instruction will teach you how to thread a sewing machine. It is designed specifically for those who are new to sewing and are unsure how their sewing machine should be strung up but are eager to give it a try and get started.

Before learning how to thread the needle on a sewing machine, you should thread the bobbin first. You can do this on the top of the sewing machine. Be certain that you are using a bobbin that is appropriate for your sewing machine.

To begin, load a bobbin by using the bobbin winder. Different sewing machines have bobbin slots at different places. On Bernina, the bobbin winding takes place on the top right, in line with the thread spools. However, on the Singer sewing machine, the bobbin was wound on the balance wheel, which was a whole different experience.

Brother sewing machine, on the other hand, uses a bobbin that is loaded from the front. If you have fumble fingers, it may be challenging at times, but if you have some patience, installing this bobbin won’t take you long at all. Read the article completely if you would like to learn how to thread a brother sewing machine.

If you examine the bobbin case in great detail, you could find a tiny screw that is just barely visible.

If your sewing machine has a bobbin that loads from the top, then the needle plate that is located below the presser foot will serve as the entry point to the bobbin holder. In this particular scenario, you will first be required to lift your presser foot in order to give the bobbin holder the opportunity to open.

It is quite unlikely that you will ever need to make any adjustments to the bobbin tension, since it is controlled at this location. I’m just highlighting that this is where you would modify the bobbin tension! Knowing how do you thread a sewing machine can take a human touch as well.

Simply place the bobbin case into the holder for the bobbin on your sewing machine. It should slide over the bobbin pin without causing any problems.

To stop the bobbin from spinning on the bobbin pin, the bobbin must be completely stuffed.

Put the bobbin back in its case and close the case.

Your sewing machine’s upper portion is now completely threaded, but the bottom component of your sewing machine still needs to be threaded.

Now, we can begin to learn how to thread the needle on a sewing machine.

Here are five simple methods you can use to thread a sewing machine.

  1. Adjust the Needle

 If you are just starting out with your sewing machine, you should not turn it on while you are threading the needle since you run the risk of the machine starting up and injuring you. You won’t need the light that is built into your sewing machine if you have other sources of light surrounding it.

While threading a sewing machine, turn the machine on and keep it running. Brother Luminaire and Babylock Destiny are two examples of high-end sewing machines that need you to switch them on in order to thread them.

There should be no twisting of the thread as it travels through the needle.

The needle should be at the most “up” position, so raise it to that position. With a handwheel, you may do it manually. To elevate the needle, you may simply push the up/down button on current computerized sewing machines, however this requires that your machine be running. This is a very important step in knowing how to thread the needle on a sewing machine.

You’ll have more freedom to move around the needle if you lower or remove the presser foot entirely. When you lower the presser foot bar, the tension discs will be engaged, preventing the thread from slipping out of your hands.

  1. Old Fashioned Methods

It is possible to thread a needle the old-fashioned method if you have a vintage sewing machine or simply a basic one. This is a very common question asked “how do you thread a sewing machine?”

Using a good pair of sharp scissors, trim the thread ends (so the cut is clean and nice without any fibres coming apart). It also helps to lick the thread. Keep your hands as near to the thread’s end as possible.

Threading the needle this manner sometimes requires several attempts on my part. Good vision and calm hands are both necessities for placing a thread in the needle!

You can see the needle eye clearly if you use a piece of white paper under the needle.

A headlamp is another option for adding more light and preventing shadows.

A pair of tweezers is an extremely helpful tool for removing the thread tail once it has passed through the needle.

Unscrewing the needle and re-threading it outside of the machine has many uses. Taking the needle out and putting it back in with the thread already attached is really fairly simple.

  1. Get a Needle Threader

The sewing industry is no exception to the contemporary world’s abundance of handy tools that teach you how to thread the needle on a sewing machine.

Because of this, sewing machine needle threaders may be purchased separately. Come along with me as I demonstrate how to make use of this tool.

Two little arrows may be seen on it. The threader should be horizontally held with either arrow pointing upward. From side to side, bring the thread over the “fork.”

Make sure you pull the threader down the needle until you hear or sense a click. Then, gently push the threader across the needle and let go of the thread. You may use the threader to force the thread through the needle’s eye by pressing down on the little metal tongue. Behind the needle eye, you’ll see a little loop.

Your hand or tweezers may be used to grab up the remainder of the thread that is left.

  1. Use Built-in Threader

Modern computerized sewing machines have built-in threaders. Check if your machine has one. Such a really small thing but quite helpful! Let’s now talk about how to use this threader.

First of all, make sure your needle is in its highest position because the threader has to line up with the eye of the needle. You can do it manually with the handwheel or push the needle up/down button (sometimes twice) if your machine has it.

Hold the thread to the left of the needle. Draw the thread down around the threader guide (or prong) with some tension and bring it from left to right in front of the needle. Once you are done, Your sewing machine’s upper portion is now completely threaded, but the bottom component of your sewing machine still needs to be threaded.

You will see that a very small hook will come out through the needle eye from the back towards the front.

Place the thread under the hook keeping the thread parallel to the table.

Release the threader knob slowly while holding the thread end with your hand. A loop of the thread will be pulled through the needle eye.

Remove the loop from the threader and pull out the thread end through the needle eye. The built-in needle threader is a marvelous design indeed; but, you need to handle it carefully since it is prone to breaking rather quickly. For instance, if the little hook that passes through the eye of the needle is curved in any way, it will pass to the side of the needle rather than through the eye of the needle. If this is the case, you will need to centre it again in order to realign it with the needle eye. You may use your fingernail or a little screwdriver to gently press it back to the centre position. This is how to thread the needle on a sewing machine.

Sometimes the hook is unable to extract a loop of the thread; in this case, the needle and the setting it was given should be double-checked.

Unfortunately, built-in needle threaders do not perform well with thick threads such as those with a weight of size ##10-30, extremely thin needles (size 65/9 and smaller), twin needles, and other types of needles. You will need to thread the needle in the typical manner given this circumstance.

  1. Thread the Needle with the Press of a Button

Sewing machines of the present era are equipped with automated needle threaders. To activate the automated threading feature, you need to essentially simply hit the appropriate button. When doing machine embroidery, in which you need to change the thread colour many times, this option is very useful and convenient.

How to Thread Double Eye Needles

These days, there are double eye needles that you can find in the market. They provide the capability of simultaneously sewing with two threads of various colours. Of course, the primary purpose for them is embroidery, but we are going to tell you about how to thread them as well.

You may go about it in the usual fashion. But you may also utilize needle threaders; the one that goes to the eye that is lower on a sewing machine is the one that comes with the machine, and the one that goes to the eye that is higher on a sewing machine is a separate purchase.

Conclusion

The above mentioned ways are the easiest for anyone to use to learn how to thread the needle on a sewing machine. It is a very simple and easy task to perform. If you need more advice, the bodies of most contemporary sewing machines have some threading guidelines inscribed on them, which you can take help of.

 

Leave a Comment